Cut-to-length-lines HITACHI

Stock-No. 1020-19439 Category Cut-to-length-lines Make HITACHI Type New in 1993 Control Location ab Werksstandort,unter Strom Origin Japan Delivery time short-dated Freight basis Ex Site - factory Price sheet width 500 - 1350 mm plate thickness 0,3 - 3 mm no. of strokes Hub/min Control total power requirement kW weight of the machine ca. t dimensions of the machine ca. m Description Stainless steel Cut to Length Line(Flying type) - Material: stainless steel, surface treated steel -- Thickness: 0.3–3 mm (as of stainless steel) -- Width: 500-1350 mm -- Trim: 5-25 mm on one side (more than twice the plate thickness) - Material coil: internal diameter 508 mm, external diameter 600–1800 mm -- weight maximum 15 tons -- Width accuracy: 500–1350 mm plus or minus 0.2 mm (when side trimming) -- Product length: 400–6000 mm Plus/minus 0.3 mm - 6-leveler (6-hi) leveler x 2units types -- Tension: 45 to 50 kg/mm2 -- Yield point: 28 kg/mm2 - Cutting method: Cut while running (flying), numerically controlled rocking type - flying shears -- (Cutting speed) 20–40/80 m/min -- Speed 2-speed change type --- 0.3 to 1.2 mm: 20 to 80 m/min --- 0.21–3 mm: 20–40 m/min -- Slow operation: 0.8 m/min -- Conveyor speed: 20~120m/min -- Cut count: up to 150 cuts/min -- (Product piling) --- Plate width: 500–1350 mm --- No1 piler: 400 to 3100 mm (also used as a reject filer) --- No2 piler: 400–6100 mm --- Load height: up to 600mm --- Load weight: up to 4 tons Line direction: From right to left on control panel Line: Approximately 13 m x 49.050 m (Major facilities) - Coil skid - Coil car - Pay off reel and a paper winder - Coil opener - Rough Leveler - Shear - No. 1 Looper Guide - Side guide and pinch roller - Side trimmer - Scrap winder x2 - No.1 Finisher Leveler (6-hi) - No2 Finisher Leveler (6-hi) - No 2 Looper Guide - Measuring roller, feed roller and paper-off reel - Shear - Conveyor - Cart - No1/No2 piler type - Hydraulic unit: Type - Valve stand type - (Coil skid) -- V-type fixed skid -- Coil maintenance: 1 coil -- Coil weight: up to 15 tonnes -- Coil diameter: 600 to 1800 mm -urethane rubber (Coil Car) Cradle roller type Hydraulic boost Electricity transfer driving type Two guide lots hydraulic cylinder elevating type (payoff reel and paper winder) Overhang, single-mant 4-segment type Paper reel motor: DC 5.5KW 400/1600 RPM, attached to brake Paper winder: cone type, (motor DC 1.5KW, 1750 RPM) (Coil Opener) Knife edge method (Rough Leveler) 2-stage (2hi) 5-body roller leveler Pinch rollers: 160 mm × 1450 mm 2 pieces, The upper part of the pinch roller is hydraulic cylinder press-down, and the lower roller is fixed 5 workload rollers 130mm x 1450mm The upper roller of the workload roller is electrically pressed, and the lower roller is fixed 0–40/80 m/min Two-stage change 0.3 to 1.6 mmt: 80 m/min 1.7 to 1.6 mmt: 40 m/min Motor: DC 18.5 KW, 1750 RPM, Brake Attachment Pressing motor: 2 1.5KW 100RPMs with brakes (Shear) Hydraulic up cut shear Knife size: 25 mm thickness × 150 mm width × 1450 mm length (No. 1 Looper Guide) Table lift Hydraulic cylinder operation method Loop: Light Volume Control Method Roller: 70 mm diameter × 1450 mm × 6 bonds, rubber lining roller (Side guide and pinch roller) Vertical Free Roller Electrically switched type Side guide roller: 90 mm diameter × 150 mm length × 6 bones Pinch Roller: 2nd Stage (2hi) Roller: 160 mm diameter × 1450 mm length × 2 bones Upper roller: pneumatic cylinder pressure free roller Lower Roller: Fixed Drive Roller (Side trimmer) Overhang Drive Cut 0–40/80 m/min 2-stage change type 0.3 to 1.6 mmt: 80 m/min 1.7 to 1.6 mmt: 40 m/min Cutter diameter: 320 mm / 190 mm internal diameter × 20 mm thickness Roller: 320 mm external diameter × 19 mm internal diameter × 20 mm thickness Motor: DC 5.5KW 1750RPM (Scrap winder) Two machines Link Pin Gauge Type (Hydraulic Cylinder Opening and Closing Type) Motor: 2 DC 2.2KW 1450 RPM (No1 Finisher Leveler) 6-level (6-hi) 17 leveler Thickness: 1.21–3.0 mm Speed: 6 to 40/80 m/min Thickness 0.3–1.2 mm 6–80 m/min Thickness 1.21–3 mm 6–40 m/min Pinch roller: 180 mm × 1750 mm × 2 bones The upper roll is a pneumatic cylinder. The lower roll is fixed Rubber lining drive roller Work roll: 60mm x 1750mm x 17e 8 for the upper roll, 9 for the lower roll Plated abrasive roller Medium roller: 50 mm × 1750 mm × 19 pieces 9 for the upper roll, 10 for the bottom roll Backup Roller: 88 mm Diameter x 50 mm Length x 7 rows Pressing Method: Lower Roller Parallel Pressing Pressing speed: 0.25 mm/sec Pressurization: plus or minus 5 mm Motor: DC 55KW 1750 RPM Brake Attachment (No2 Finisher Leveler) 6-level (6-hi) 17 leveler Plate thickness: 0.3–1.2 mm Speed: 5 to 80 m/min Pinch roller: 180 mm × 1750 mm × 2 bones The upper roll is a pneumatic cylinder. The lower roll is fixed Rubber lining drive roller Work roll: 35mm x 1750mm x 17bon 8 for the upper roll, 9 for the lower roll Plated abrasive roller Medium Roller: 32 mm × 1750 mm × 19 pieces 9 for the upper roll, 10 for the bottom roll Backup Roller: 99 mm Diameter x 50 mm Length x 7 rows Roller bearing type Pressing Method: Lower Roller Parallel Pressing Pressing speed: 0.25 mm/sec Pressurization: plus or minus 5 mm Motor: DC 35KW 1750RPM Brake Attachment (No. 2 Looper Guide) Table lift Hydraulic cylinder operation method Loop: How to control the amount of light (amount of light) Roller: 70 mm diameter × 1450 mm × 6 bonds, rubber lining roller (Measuring roll/feed roller/paper vinyl payoff reel) Measuring roller: The upper roll is pneumatic pressing, the lower roll is fixed, the pressing amount is 30 mm Feed roller: Upper roll is pneumatic cylinder press, lower roll is fixed, press load is 40 mm Motor: DC 2.2KW 1750RPM (Shear) Fluctuating Flying shear 0.3~3mm Speed: 2 groups of 20–40/80 m/min Thickness 0.3–1.6 mm 80 m/min Tlate thickness 1.6–3 mm 40 m/min Cut count: up to 150 cuts/min Cutting length: 400–6000 mm Electric up CUT shear Cut up and down knife die via motor, reducer, pinion stand crankshaft Knife: 20 mmt × 80 mm × 1400 mm × 1 set The top knife is a straight knife, and the bottom is a V-lock knife Adjustment: Wedge Motor: DC 75KW 550RPM (Conveyor) Belt conveyor type Belt width: 1200 mm Conveyor length: 3800 mm Motor DC 5.5KW 1450RPM Brake Attachment (No. 1 No. 2 piler) No1 piler: Combined use of reject truck, air blower Combined use of side conveyor No2 piler: Combined suction conveyor and air blower Loading height: 600 mm Lift: Hydraulic lift volume 650 mm Motor: 4 1.5KW 150RPM units for side guide end stoppers 2.2 KW 1500RPM for lifters 1.5KW for cart 7.5KW for blower (Hydraulic device) 70 kg/cm2 × 100 L/min Pen pump Motor: DC 18.5 KW 1000 RPM (Supply power) AC400 V,50 Hertz 3 Phase / AC200 V,50 Hertz 3 Phase (Control power) AC 200V, 50 Hz Single Phase (Compressed air) Compressed air required: 5 kg/cm2

No documents were found.

No videos were found.

Stock-No.	1020-19439
Category	Cut-to-length-lines
Make	HITACHI
Type
Company
Business
Name
Street
Zipcode / Place
Country	Please choose ... Afghanistan Albanien Algerien Andorra Angola Argentinien Armenien Aserbeidschan Australien Bahamas Bahrain Bangladesch Belarus Belgien Belize Bolivien Bosnien/Herzegowina Botswana Brasillien Bulgarien BurkinaFaso Burundi Chile China CostaRica Deutschland DominikanischeRepublik Dänemark Ecuador Elfenbeinküste ElSalvador Estland Finnland Frankreich Gabun Gambia Georgien Ghana Granada Griechenland Grossbritannien Guatemala Guayana Guinea Haiti Honduras Hongkong Indien Indonesien Irak Iran Irland Island Israel Italien Jamaika Japan Jemen Jordanien Jugoslawien Kambodscha Kamerun Kanada Kasachstan Katar Kenia Kirgistan Kolumbien Kongo Kosovo Kroatien Kuba Kuweit Laos Lesotho Lettland Libanon Liberia Liechtenstein Litauen Luxemburg Lybien Madagaskar Malaysia Malediven Mali Malta Marokko Mexiko Moldawien Monaco Mongolei Mosambik Namibia Nepal Neuseeland Nicaragua Niederlande Niger Nigeria Nordkorea Norwegen Oman Pakistan Panama Papua-Neuguinea Paraguay Peru Philippinen Polen Portugal Rep.Mazedonien Ruanda Rumänien Russland Sambia Saudi-Arabien Schweden Schweiz Senegal Seychellen SierraLeone Simbabwe Singapur Slowakei Slowenien Somalia Spanien SriLanka Sudan Südafrika Südkorea Syrien Tadschikistan Taiwan Tansania Thailand Togo TrinidadundTobago Tschad TschechischeRepublik Tunesien Turkmenistan Türkei Uganda Ukraine Ungarn Uruguay USA Usbekistan Vatikanstadt Venezuela VereinigteArabischeEmirate Vietnam Weißrussland Zwasiland Zypern Ägypten Äthiopien Österreich
Phone
Fax
Email
Offer via	E-Mail Mail Phone Fax
Your message